This content has been marked as final. Show 5 replies
When starting the EC - it can take a good few minutes for the service to start up.
Next time, you can run:
/opt/SUNWxvmoc/bin/ecadm start -w -v
The "-w" is for "wait" - so the start command will actually wait until the service is up and running before going back to prompt.
If it still fails, check what service doesn't start properly:
# svcs '*scn*' '*common*'
This can give you a good starting point.
Last, once you're done with starting with "-w" (or even before you run it), try checking for known issues with the OCDoctor:
# /var/opt/sun/xvm/OCDoctor/OCDoctor.sh --update
# /var/opt/sun/xvm/OCDoctor/OCDoctor.sh --troubleshoot
Thank you Eran for pointing me in the right direction!
I"ve noticed that I have several services disabled and one in maintenance, but the most helpful thing was this output from OCDoctor:
ERROR: SUNWj6rt version (1.6.0_31) does not match SUNWj6rtx version (1.6.0_26)
Make sure that the 32 bit matches the 64 bit version, otherwise you may have issues starting the EC.
So my first task will be to make both packagaes have the same version number, and then continue from there.
I'll post here the results. Thanks again
I've installed the patches 125136-37.zip 125137-37.zip, now the java versions are in the same release level but the problem persists.
I've checked the running services and here's the output:
[root->/]# svcs '*scn*' '*common*'
STATE STIME FMRI
legacy_run Aug_22 lrc:/etc/rcS_d/S88SUNWscn-update-agent-prepare-singleuser
legacy_run Aug_22 lrc:/etc/rcS_d/S90SUNWscn-update-agent-singleuser
disabled Aug_22 svc:/application/scn/singleuser-agent:default
disabled Aug_22 svc:/application/scn/update-agent:default
disabled Aug_22 svc:/application/management/common-agent-container-1:default
disabled Aug_22 svc:/application/scn/db:remote
disabled Aug_22 svc:/application/scn/ec-server-splashpage:default
disabled Aug_22 svc:/application/scn/dhcpd:default
online Aug_22 svc:/application/scn/satellite-enable:default
online Aug_22 svc:/application/scn/ajaxterm:default
online Aug_22 svc:/application/scn/oralistener:default
online Aug_22 svc:/application/scn/oracle:default
online Aug_22 svc:/application/scn/db:local
online Aug_22 svc:/application/scn/db:default
online Aug_22 svc:/application/scn/uce-scheduler:default
online Aug_22 svc:/application/management/common-agent-container-1:oem-ec
online Aug_22 svc:/application/scn/proxy-enable:default
online Aug_22 svc:/application/management/common-agent-container-1:scn-proxy
online Aug_22 svc:/application/scn/proxy-available:default
offline Aug_22 svc:/application/scn/satellite-available:default
maintenance 16:11:52 svc:/application/scn/uce-server:default
I don't know if the disabled services are ok or if I should try to start them; regarding the service in maintenance mode, here's the problem shown in the log:
[ Aug 22 12:18:24 Executing start method ("/opt/SUNWxvmoc/lib/methods/scn-uce-server start") ]
(126)Cannot assign requested address: make_sock: could not bind to address 192.168.40.101:8002
no listening sockets available, shutting down
That IP (192.168.40.101) is not longer valid in the server (it was when I installed Enterprise Manager but now is wrong); my question is: where is this IP information stored in Enterprise Manager so I can change it to the correct value?
Thanks in advance,
I run into numerous problems with this upgrade, spent 6 full working days with different ways of upgrading and fiddling around to no avail.
In the end I just reinstalled 12cU1 from scratch and manually re-added all assets and did the configuration again, it was way faster.
Also the new agent version (b2083) seemed to fix a lot of problems so remember to upgrade your agents as well.