1 Reply Latest reply: Nov 6, 2013 3:13 AM by Pascal Kreyer -Oracle RSS

    Can Anyone Tell Us What CPU This Blade Log Has? (SPARC T3-1B) - PLEASE

    a9fd24d1-3f2b-45f3-be1c-6f4375d93b88

      Primary Bootstrap.

       

       

       

       

      U-Boot 1.1.4

       

       

      Custom AST2100 U-Boot 3.0 (Feb  4 2011 - 00:21:51) r62572

       

       

      DRAM:  119 MB

      Flash bank 0 at 10000000 has 32MB in 256 sectors (chipSize 1<<25, ratio 1, bufSz 64).

      Flash: 32 MB

      VUART1 at port 0x03f8, SerIRQ[4] disabled

      VUART2 at port 0x02f8, SerIRQ[3] disabled

      Protecting U-Boot flash sectors; monitor_base=100a0000.

      board_findGpioNum(): ERROR, 'BIOS_TOP_BLOCK_LOCK' does not match any pin.

      board_findGpioNum(): ERROR, 'SP_PECI_ENABLE' does not match any pin.

      H/W:   Virgoplus Service Processor; SOC: AST2100 Rev. 02 ('A3')

        PWC_SP_Broken_OD = 0;  ARM restart caused by: power-on

        The host is OFF(held) (hostWantsPwr=1, powerGood=0,

              allowPwrOn=0|0, outOfReset=0, fatalError=0).

        Reset straps=0x8c819180, def. H-PLL=264 MHz, CPU/AHB=2:1, boot CS0# normal speed

        PCI w/VGA noVBIOS;  NOR 38ns/byte;  DRAM clock is M-PLL: 264 MHz (DDR2-528)

        DRAM: 128MB data - 8MB VGA, 32-bit noECC, 2 BA 10 CA, CL=4 BL=4 ap=1, 61440 us refr, DQSipv=0x2020202

      Board Revision - 8d

      Date: 2013-11-05 (Tuesday)    Time: 16:15:08

      Reading FRUID...Valid CRC.

      ethaddr=00:21:28:BB:FD:76

      eth1addr=00:21:28:BB:FD:77

      Platform (virgo): Configuring HPC FPGA (data=0x100ed800, len=45844)

      ## Extracting HPC microcode...done

      Now programming 225844 bytes...

      HPC programming done, rc = 0

      HPC_FPGA_DONE = 1

      Net:   faradaynic#0, faradaynic#1

      Enter Diagnostics Mode ['q'uick/'n'ormal(default)/e'x'tended(manufacturing mode)] .....   0

      Diagnostics Mode - NORMAL

      <DIAGS> Memory Data Bus Test ... PASSED

      <DIAGS> Memory Address Bus Test ... PASSED

      I2C Probe Test - Motherboard

              Bus     Device                          Address Result

              ===     ============================    ======= ======

               1               PCA9548 MUX (U3004)    0xE2    PASSED

               2                 Sys FRUID (U3003)    0xA0    PASSED

               2                Power CPLD (U3301)    0x4E    PASSED

               2          CPU0 Fault LED's (U3001)    0x40    PASSED

               2          CPU1 Fault LED's (U3002)    0x42    PASSED

               2            PCA9555 (Misc) (U3005)    0x44    PASSED

               2        Temp. Sensor(LM75) (U3006)    0x90    PASSED

               2                   LTC4215 (U5102)    0x96    PASSED

               2                 DIMM IMAX (U3102)    0x12    PASSED

               6          Bank Panel Led's (U3406)    0xC6    PASSED

               6               DS1338(RTC) ( U803)    0xD0    PASSED

       

       

      <DIAGS>Testing 4eyes access .... PASSED

      <DIAGS> PHY #0 R/W Test ... PASSED

      <DIAGS> PHY #0 Link Status ... PASSED

      <DIAGS> ETHERNET PHY #0, Internal Loopback Test ... PASSED                                                           <DIAGS> USB 1.1 Test ... PASSED

      <DIAGS>Access to BIOS Flash ... PASSED

      <DIAGS> Testing PowerCPLD version ... PASSED

      checking for abnormal reboots: 0:0.

      abnormal reboot found -- too long, ignore

      Booting linux in 3 seconds...

      Un-Protect Flash Bank # 1

      flctrl: Recovery U-Boot (r56177) at 0x10040000 is valid (min. r51654).

      Trying primary image...

      Trying to boot package at 10100000

      Found kernel image at 10102000

      Found root image at 1025f9f4

      copying 0x00a8d040 bytes from 0x1025f9f4 to 0x00800000

      bootargs= root=/dev/ram  ramdisk_size=10804  console=ttyS0,9600 bigphysarea=6144 ractrends.mtdblocks=env,0x20000,0x20000,coredump,0x1500000,0x800000,persist,0x1d00000,0x200000,params,0x1f00000,0x100000,

      ## Booting image at 10102000 ...

         Image Name:   Linux-2.6.27.43

         Created:      2011-02-04   5:18:45 UTC

         Image Type:   ARM Linux Kernel Image (uncompressed)

         Data Size:    1431988 Bytes =  1.4 MB

         Load Address: 00008000

         Entry Point:  00008000

         Verifying Checksum ... OK

      OK

      do_bootm_linux() armlinux.c:104

        bootm

        0x10102000

        0x00800000

      theKernel=00008000

      do_bootm_linux() armlinux.c:121 - 9

      ## Loading Ramdisk Image at 00800000 ...

      do_bootm_linux() armlinux.c:155 - 10

         Image Name:

         Created:      2011-02-04   6:07:05 UTC

         Image Type:   ARM Linux RAMDisk Image (uncompressed)

         Data Size:    11063296 Bytes = 10.6 MB

         Load Address: 00000000

         Entry Point:  00000000

         Verifying Checksum ... OK

      do_bootm_linux() armlinux.c:182 - 11

      do_bootm_linux() armlinux.c:245 - 15

      arch_number = 0x00000386

      env_t       = 0x01ED0008

      boot_params = 0x40000100

      DRAM bank   = 0x00000000

      -> start    = 0x00000000

      -> size     = 0x07700000

      ethaddr     = 00:21:28:BB:FD:76

      eth1addr    = 00:21:28:BB:FD:77

      ip_addr     = 0.0.0.0

      baudrate    = 9600 bps

      Sun extensions:

        bi_UBootEnvAddr     = 0x10020000

        bi_UBootEnvSize     = 0x00020000

        bi_flashstart       = 0x10000000

        bi_flashsize        = 0x02000000

        bi_flashbanksize    = 0x02000000

        bi_flashbanks       = 0x01

        bi_flashbankwidth   = 0x01

        bi_flashsectorsize  = 0x00020000

        bi_flashsectorcount = 0x00000100

        bi_boottype         = 0x02

        bi_primarytype      = 0x02

        bi_secondarytype    = 0x00

        bi_booted           = 0x10100000

        bi_primary          = 0x100a0000

        bi_secondary        = 0xffffffff

        bi_primaryhdr       = 0x10100000

        bi_secondaryhdr     = 0xffffffff

        bi_imagearea0       = 0x100a0000

        bi_imagearea1       = 0xffffffff

        bi_maximagesize     = 0x01f60000

        bi_min_firmware_rev = 0

        bi_sptrace_base     = 0x00000000

        bi_sptrace_len      = 0x00000000

        bi_apbclockhz       = 0x03ef1480

       

       

      H/W:   Virgoplus Service Processor; SOC: AST2100 Rev. 02 ('A3')

        The host is OFF(held) (hostWantsPwr=1, powerGood=0,

              allowPwrOn=0|0, outOfReset=0, fatalError=0).

        ARM Control reg: RR=0 HV=0 IC=1 BPd=0 RomP=0 SysP=0 BE=0 WB=1 DC=0 AlinFlt=1 MMU=0

        Cache Type reg: CType=0xe WB, sep.; I: 16KB of 32B lines 4-way; D: 16KB of 32B lines 4-way

              IC locked ways(3:0): 0000b, DC locked ways: 0000b

        Reset straps=0x8c819180, def. H-PLL=264 MHz, CPU/AHB=2:1, boot CS0# normal speed

        H-PLL (params=0x04291) 264.000 MHz, M-PLL params=0x04120-->264.000 MHz

        CPUCLK: H-PLL/1=264 MHz, AHB HCLK: CPUCLK/2=132 MHz, APB PCLK: H-PLL/4= 66 MHz

        PCI w/VGA noVBIOS;  NOR 38ns/byte;  DRAM clock is M-PLL: 264 MHz (DDR2-528)

        Bus-master-mode clocks: PCI BHCLK= 33 MHz, LPC LHCLK= 33 MHz

        Stopped clocks: vidCap-1, SP-Display, HACE, PCI-host

        DRAM: 128MB data - 8MB VGA, 32-bit noECC, 2 BA 10 CA, CL=4 BL=4 ap=1, 61440 us refr, DQSipv=0x2020202

        Reset controls: HACE, PwmFt, displays, MDMA, PCI-host

        Register protect: SCU prot, DMC prot, AHBC prot, VIC U-prot

        Ethernet MAC-PHY interface mode=6 (RMII + RMII), no MII2DC+DIO pins

      do_bootm_linux() armlinux.c:260

      do_bootm_linux() armlinux.c:263

      do_bootm_linux() armlinux.c:267

      do_bootm_linux() armlinux.c:279

      do_bootm_linux() armlinux.c:283

      do_bootm_linux() armlinux.c:287

      do_bootm_linux() armlinux.c:295

      Galactic register 1: 400509c0

      Starting watchdog timer.

       

       

      Starting kernel at 0x00008000...

       

       

      do_bootm_linux() armlinux.c:320

      do_bootm_linux() armlinux.c:324 (0x00000386,0x40000100)

      Uncompressing Linux............................................................................................... done, booting the kernel.

      Linux version 2.6.27.43 (buildbot@build-slave-sh-8) (gcc version 3.3.6) #1 Fri Feb 4 00:18:12 EST 2011

      CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177

      Machine: ASPEED-AST2100

      Memory policy: ECC disabled, Data cache writeback

      CPU0: D VIVT write-back cache

      CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets

      CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets

      Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 30226

      Kernel command line: root=/dev/ram  ramdisk_size=10804  console=ttyS0,9600 bigphysarea=6144 ractrends.mtdblocks=env,0x20000,0x20000,coredump,0x1500000,0x800000,persist,0x1d00000,0x200000,params,0x1f00000,0x100000,

      PID hash table entries: 512 (order: 9, 2048 bytes)

      console [ttyS0] enabled

      mach/timer.c: Just lost 80 clock interrupts.

      Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

      Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

      Memory: 119MB = 119MB total

      Memory: 82144KB available (2708K code, 246K data, 124K init)

      Calibrating delay loop... 131.48 BogoMIPS (lpj=657408)

      Mount-cache hash table entries: 512

      Initializing cgroup subsys ns

      Initializing cgroup subsys cpuacct

      CPU: Testing write buffer coherency: ok

      net_namespace: 804 bytes

      NET: Registered protocol family 16

      NET: Registered protocol family 2

      IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

      TCP established hash table entries: 4096 (order: 3, 32768 bytes)

      TCP bind hash table entries: 4096 (order: 2, 16384 bytes)

      TCP: Hash tables configured (established 4096 bind 4096)

      TCP reno registered

      NET: Registered protocol family 1

      checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd

      Freeing initrd memory: 10804K

      NetWinder Floating Point Emulator V0.97 (double precision)

      bigphysarea: Allocated 6144 pages at 0xc128e000.

      squashfs: version 3.4 (2008/08/26) Phillip Lougher

      squashfs: LZMA suppport for slax.org by jro

      JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.

      msgmni has been set to 181

      Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)

      io scheduler noop registered (default)

      ttyS0 at MMIO 0x1e783000 (irq = 9) is a GUC-ASPEED UART

      ttyS1 at MMIO 0x1e784000 (irq = 10) is a GUC-ASPEED UART

      brd: module loaded

      loop: module loaded

      FTGMAC100: ASPEED FTGMAC Driver, (Linux Kernel 2.6.15.7) 11/17/2008 - by ASPEED

      FTGMAC100: eth0: at 0xfe660000 IRQ:2 noWait:0, MAC 00:21:28:bb:fd:76

      FTGMAC100: eth0:ftgmac100_reset, phyAddr=0x0, miiPhyId=0x0040_61e4

      FTGMAC100: lp->rx_descs = ffc00000, lp->rx_rx_descs_dma = 67ac000

      FTGMAC100: lp->rx_buf = 00000000, lp->rx_buf_dma = 0

      FTGMAC100: lp->tx_descs = ffc01000, lp->tx_rx_descs_dma = 67bd000

      FTGMAC100: lp->tx_buf = 00000000, lp->tx_buf_dma = 0

      FTGMAC100: eth1: at 0xfe680000 IRQ:3 noWait:0, MAC 00:21:28:bb:fd:77

      FTGMAC100: eth1:ftgmac100_reset, phyAddr=0xff, miiPhyId=0x0000_0002

      FTGMAC100: lp->rx_descs = ffc02000, lp->rx_rx_descs_dma = 67c1000

      FTGMAC100: lp->rx_buf = 00000000, lp->rx_buf_dma = 0

      FTGMAC100: lp->tx_descs = ffc03000, lp->tx_rx_descs_dma = 67d4000

      FTGMAC100: lp->tx_buf = 00000000, lp->tx_buf_dma = 0

      Ractrends Flash mapping: 0x2000000 at 0x10000000

      Bank #0: Found 1 x16 devices at 0x0 in 8-bit bank

      Amd/Fujitsu Extended Query Table at 0x0040

      Bank #0: CFI does not contain boot bank location. Assuming top.

      number of CFI chips: 1

      Number of banks found = 1

      GetMTDPartitions() says string is "env,0x20000,0x20000,coredump,0x1500000,0x800000,persist,0x1d00000,0x200000,params,0x1f00000,0x100000,"

      MTD Partition 0 : fullpart @ 0x0 of Size 0x2000000

      MTD Partition 1 : env @ 0x20000 of Size 0x20000

      MTD Partition 2 : coredump @ 0x1500000 of Size 0x800000

      MTD Partition 3 : persist @ 0x1d00000 of Size 0x200000

      MTD Partition 4 : params @ 0x1f00000 of Size 0x100000

      Creating 5 MTD partitions on "Bank #0":

      0x00000000-0x02000000 : "fullpart"

      0x00020000-0x00040000 : "env"

      0x01500000-0x01d00000 : "coredump"

      0x01d00000-0x01f00000 : "persist"

      0x01f00000-0x02000000 : "params"

      wdt: AST2100 WDT is installed.

      wdt: AST2100 WDT nowayout = 1, heartbeat = 30 secs

      wdt: AST2100 WDT guardstartupshutdown = 1

      wdt: AST2100 WDT startuptimeout = 600, shutdowntimeout = 60

      wdt: AST2100 WDT was enabled at driver start, time remaining 53 secs.

      wdt: Guarding startup, setting watchdog for 600 seconds.

      nf_conntrack version 0.5.0 (2048 buckets, 8192 max)

      CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Plase use

      nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or

      sysctl net.netfilter.nf_conntrack_acct=1 to enable it.

      ip_tables: (C) 2000-2006 Netfilter Core Team

      TCP cubic registered

      NET: Registered protocol family 10

      ip6_tables: (C) 2000-2006 Netfilter Core Team

      NET: Registered protocol family 17

      RPC: Registered udp transport module.

      RPC: Registered tcp transport module.

      802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>

      All bugs added by David S. Miller <davem@redhat.com>

      drivers/rtc/hctosys.c: unable to open rtc device (rtc0)

      RAMDISK: squashfs filesystem found at block 0

      RAMDISK: Loading 10801KiB [1 disk] into ram disk... done.

      VFS: Mounted root (squashfs filesystem) readonly.

      Freeing init memory: 124K

      INIT: version 2.86 booting

      Creating /var tmpfs

      Creating directories in /var...done.

      Creating /var/log tmpfs...done.

      Calculating module dependencies... done.

      Loading modules...

          flashinfo

          helper

      Helper Module Driver Version 1.1

      mach/timer.c: Just lost 2 clock interrupts.

      Copyright (c) 2006 American Megatrends Inc.

          dbgpersist

      Persistent Driver Debugger version 1.1

      Copyright (c) 2008 Sun Microsystems Inc.

              Loading debug: usbhub [success]

              1 debug modules loaded

          gpiomgr

          gpioint

          peci

      PECI Driver: peci_initialize_device(696) Setup device peci0.

          i2c-core

      i2c_boardinfo: module license 'unspecified' taints kernel.

          i2c-dev

      i2c /dev entries driver

          i2c-algo-as

          i2c-aspeed

      i2c-adapter i2c-0: Hardware routines registered

      Registered bus id: i2c-0

      i2c-adapter i2c-1: Hardware routines registered

      Registered bus id: i2c-1

      i2c-adapter i2c-2: Hardware routines registered

      Registered bus id: i2c-2

      i2c-adapter i2c-3: Hardware routines registered

      Registered bus id: i2c-3

      i2c-adapter i2c-4: Hardware routines registered

      Registered bus id: i2c-4

      i2c-adapter i2c-5: Hardware routines registered

      Registered bus id: i2c-5

      i2c-adapter i2c-6: Hardware routines registered

      Registered bus id: i2c-6

          i2c-boardinfo

          videocap

      AST Video Capture Driver Version 1.0

      Copyright (c) 2005-2006 American Megatrends Inc.

          usb

      Initializing USB Devices -

      USB Device Endpoint Driver

      Copyright 2006 American Megatrends Inc.

      usb_init(): --USB INITIALIZING-- version MOD-VER:2011-02-04,00:09:46 with UsbEth and EndPoint-Remapping: 1

      USB GlobalDisconnect(): Called

      (E)ethBot_ConvertMacStr: converting '002128574716'

      Init AST11 Success

      USB GlobalReconnect(): Called

      mach/timer.c: Just lost 2 clock interrupts.

      USB Driver is Successfully Initialized

          btkcs

      All modules loaded.

      ... done.

      Checking device file systems

      Finished check of device file systems

       

       

      Checking configuration files state ...

      Image date:  Fri Feb  4 01:06:21 EST 2011       Image revision: 62572

      Conf date:   Fri Feb  4 01:06:21 EST 2011       Conf revision:  62572

      Configuration files state good after upgrade.

       

       

      Starting Platform Initialization: platinit.

      Running ldconfig...done

       

       

      Starting Platform Initialization: c10init.

      Starting FRU update program, platform id phase: frutool.

      Starting spdiag Platform Init: /usr/local/bin/spdiag  Done (0)

      Setting up networking...done.

      Hostname: SUNSP-1113FMN04D.

       

       

      Setting up IP spoofing protection: rp_filter.

      Configuring IPv6...done

      Configuring network interfaces...FTGMAC100: eth0:ftgmac100_open

      mach/timer.c: Just lost 3 clock interrupts.

      FTGMAC100: eth0:ftgmac100_reset, phyAddr=0x0, miiPhyId=0x0040_61e4

      FTGMAC100: eth1:ftgmac100_open

      FTGMAC100: eth1:ftgmac100_reset, phyAddr=0xff, miiPhyId=0x0000_0002

      SIOCSIFNETMASK: Cannot assign requested address

      SIOCSIFBRDADDR: Cannot assign requested address

      Failed to bring up eth1.

      done.

      Starting Constellation Blade Daemon: c10bd.

      Running ldconfig...done

      Starting portmap daemon: portmap.

      Starting ILOM Watchdog daemon.

      wdt: WDT device opened.  Watchdog starting with heartbeat = 30 secs

      mach/timer.c: Just lost 6 clock interrupts.

      wdt: AST2100 WDT was enabled at driver open, time remaining 556 secs.

      Done

      populating memstore vars from disk

      Running plat...plat: platform=b10, chassis=c01

      Done running plat

      Identifying Product Data...done.

      Starting FRU info cache program: frucache.

      INIT: Entering runlevel: 3

      Preparsing sensor.xml...

      Starting Shared Sensor Broadcast Daemon: ssbcastd  Done

      Starting system log daemon: syslogd and klogd.

      Starting capidirect daemon: capidirectd . Done

      Starting Event Manager: eventmgr  . Done

      Starting ipmi log manager daemon: logmgr . Done

      Starting System Avoidance Daemon: sad  Done

      Starting user mgmt upgrade program: usrmgt_upgrade.

      Starting the Health Monitor Daemon...

      Starting portmap daemon: portmap.

      Starting Host console Daemon: consd . Done

      Starting capidirectd: Done.

      Starting Error Telemetry Collection Daemon: etcd . Done

      Starting Fault Diagnosis Daemon: fdd . Done

      Starting IPMI Stack: . Done

      SSH RSA Host Key Files already exist. Skipping key creation ...

      SSH DSA Host Key Files already exist. Skipping key creation ...

      Starting sshd.

      Starting OpenBSD Secure Shell server: sshd-man.

      Starting SP fishwrap cache daemon: fishwrapd . Done

      Starting Network Controller Sideband Interface Daemon: ncsid . Done

      Starting Platform Obfuscation Daemon: pod . Done

      Starting lu main daemon: lumain . Done

      Starting HT sign on daemon: htsignond . Done

      Starting webgo Web Server: webgo . Done

      Starting Detection/Diagnosis After System Boot: dasboot  Done

      Starting Shared Sensor Poller: sspoller  Done

      Starting Servicetags discoverer: stdiscoverer.

      Starting Servicetags listener: stlistener.

      Starting Dynamic FRUID Daemon: dynafrud  Done

      Starting FRU info cache program: frucache.

       

       

      SUNSP-1113FMN04D login: