5 Replies Latest reply on Jun 19, 2015 6:40 PM by goj

    patching R12.2.4

    goj

      Hi All,

       

      I have 2 patches to apply to my environment.

      197xxxx and 205xxxx,  a translation and an HR patch.

       

      So the question is, after setting ADOP phase=apply patches=192xxxxx

      , can i run APPLY again before doing the rest of the ADOP steps, like cutover, etc etc?

       

      meaning:

       

      After patch has been applied successfully, Complete the below patch cycles.

      $ adop phase=finalize

      $ adop phase=cutover

      $ adop phase=cleanup

       

       

      5) Synchronize the file system, which copy the new run edition code and configuration to the patch file system.

      $ adop phase=fs_clone  _---------> Is THIS necessary?

       

      thank you

        • 1. Re: patching R12.2.4
          Pravin Takpire

          Yes it is required to complete the steps

          regards

          Pravin

          • 2. Re: patching R12.2.4
            Bashar.

            Hi,

             

            If you mean that you want to apply more patches in the same cycle then the answer is yes.

            Apply all patches and then continue with the rest of the phases.

             

            Regards,

            Bashar

            • 3. Re: patching R12.2.4
              goj

              Hi

               

              The APPLY phase completed, Now I am running FINALIZE phase and it fails:

               

               

               

              attaching log file...thank you

              • 4. Re: patching R12.2.4
                goj

                the atrtached file is for failed FINALIZE phase. 

                • 5. Re: patching R12.2.4
                  goj

                  So I don't understand this:

                   

                  adop -status says:  (upgrading to RD.4)

                   

                  Node NameNode TypePhase    Status    Started   Finished  Elapsed

                  --------------- --------------- ----------- --------------- ------------------------------ ------------------------------ ------------

                  ebswlmasterPREPARE     COMPLETED    17-JUN-15 07:29:46 -07:00   17-JUN-15 07:44:25 -07:00  0:14:39
                  APPLY    FAILED    19-JUN-15 12:01:05 -07:00   19-JUN-15 01:59:14 -07:00  1:58:09
                  CUTOVER     NOT STARTED
                  CLEANUP     NOT STARTED

                   

                   

                  But,

                  the adop apply patch completed successfully:

                   

                  ATEMENT] [START 2015/06/19 01:59:16] Generating Report to spool all logs from ad_zd_logs

                          [STATEMENT] Report: /data/nfs_share/d01/oracle/PROD/fs1/EBSapps/appl/ad/12.0.0/sql/ADZDSHOWLOG.sql

                   

                   

                          [STATEMENT] Output: /data/nfs_share/d01/oracle/PROD/fs_ne/EBSapps/log/adop/21/apply_20150619_000001/PROD_ebswl/adzdshowlog.out

                   

                   

                        [STATEMENT] [END   2015/06/19 01:59:19] Generating Report to spool all logs from ad_zd_logs

                      [STATEMENT] [END   2015/06/19 01:59:20] Generating AD_ZD_LOGS Report

                    [STATEMENT] [END   2015/06/19 01:59:20] Generating Post Apply Reports

                    [STATEMENT] SQL Statement:       update ad_adop_sessions

                          set status='C'

                           where adop_session_id = 21 and appltop_id = 195 and node_name='ebswl'

                   

                   

                  [STATEMENT] [END   2015/06/19 01:59:23] adzdoptl.pl run

                  [STATEMENT] adop phase=apply - Completed Successfully

                   

                  **********

                   

                  so why are 2 difft outputs?

                  Is this why the FINALIZE phase is failing?  or should I just run the CUTOVER anyway?