3 Replies Latest reply: Aug 28, 2009 5:20 AM by sunpraveen RSS

    OID 10.1.4.2.0 for Linux Preview Install errors: Error reading 'ods' passwd

    276393
      I'm trying to install the Oracle Internet Directory 10.1.4.2.0 for Linux Preview Release on OEL 2.6.9-55.0.12.0.1.ELsmp and I'm getting the following error during the configuration:

      [root@oid1b]# rpm -ivh oracle-oid-10.1.4.2.0-1.0.i386.rpm oracle-xe-univ-10.2.0.1-1.0.i386.rpm
      Preparing... ########################################### [100%]
      1:oracle-xe-univ ########################################### [ 50%]
      Executing Post-install steps...

      You must run '/etc/init.d/oracle-xe configure' as the root user to
      configure the database.

      2:oracle-oid ########################################### [100%]

      Installed OID software successfully

      Please refer /usr/lib/oracle/oid/ldap/doc/OID-RPM-QuickStartGuide.pdf for documentation

      To complete the installation and configuration of OID,

      execute following command as the root user:

      /etc/init.d/oracle-oid configure

      If the XE database is not already configured, the above command will configure it.

      Please execute this command now.


      [root@oid1b]# /etc/init.d/oracle-oid configure
      config-oid detected that Oracle XE is not Configured
      Do you want to configure now [y]:
      Configuring Oracle XE, This may take a few minutes ...

      Oracle Database 10g Express Edition Configuration
      -------------------------------------------------
      This will configure on-boot properties of Oracle Database 10g Express
      Edition. The following questions will determine whether the database should
      be starting upon system boot, the ports it will use, and the passwords that
      will be used for database accounts. Press <Enter> to accept the defaults.
      Ctrl-C will abort.

      Specify the HTTP port that will be used for Oracle Application Express [8080]:

      Specify a port that will be used for the database listener [1521]:

      Specify a password to be used for database accounts. Note that the same
      password will be used for SYS and SYSTEM. Oracle recommends the use of
      different passwords for each database account. This can be done after
      initial configuration:
      Confirm the password:

      Do you want Oracle Database 10g Express Edition to be started on boot (y/n) [y]:

      Starting Oracle Net Listener...Done
      Configuring Database...Done
      Starting Oracle Database 10g Express Edition Instance...Done
      Installation Completed Successfully.
      To access the Database Home Page go to "http://127.0.0.1:8080/apex"
      Configuration for Oracle XE finished.

      Oracle Internet Directory 10.1.4.2 Preview 1 Configuration
      ----------------------------------------------------------

      Enter the Oracle XE database 'sys' user password:

      Choose a password for the OID Administrator, 'cn=orcladmin':
      Confirm OID Administrator Password:

      Specify the non-SSL LDAP port to be used by OID server [389]:

      Specify the SSL LDAP port to be used by OID server [636]:

      Specify the Naming Context to be used [dc=com]: dc=beaumont,dc=edu

      If this OID will be used for Linux authentication, you might want to
      configure OID with SSL server side authentication.

      Note: Configuring OID with SSL server side authentication will generate
      a self signed certificate, which is not intended for production.

      Please refer to the documentation on setting up production certificates.

      Do you want to configure OID with SSL server side authentication? [y]:

      ###############################................................................................ [35%]gsluwpwaGetWalletPasswd: Opening 3 file failed with error 11005
      [gslusw]:Error reading 'ods' passwd from wallet
      [gsdsiConnect]:Error reading 'ods' passwd from wallet
      Could not connect to the Database.


      Any suggestions?