Here is the list of the questions sent out during the webinar and the answers that were provided.
How did you get to "create inventory" screen?
Just navigate to Lists > Accounting > Items > New > Inventory Item.
We use a lot of kit items in orders. It doesn't seem like NetSuite registers the component inventory item sales for calculating Inventory Management metrics like reorder points. Is this possible and where is a good place to learn more about how to do this?
Reorder Points are auto-calculated on the component item level and not on the kit/package level. Sales of kits/packages, however, will still be accounted for on the component level, hence, incorporated when determining demand history for such component item.
Is the following true: inventory levels below preferred will not trigger ordering - its only when it gets down to reorder point, is that correct?
Yes, this is correct. The item will only be listed on the order items page when the reorder point is reached.
Will multiple POs be generated if you created an order with multiple vendors in the Order Items page?
Yes, multiple Purchase Orders will be created.
The automatic order cause the PO to be approved automatically. Is this done via suite approvals?
It is an expected behavior and is logged as Enhancement 391339 Transactions > Purchases > Order Items Page > Create a Purchase Order > Status is Approved by Supervisor/Pending Receipt.
Can you create an inventory count using a bin range instead of counting all items across an entire location across all bins?
Unfortunately, it is not yet possible to create an inventory count based on bins as it's not included as available filter on the page.
Can Net Suite calculate an ABC classification to aid in Identifying items for Cycle counting?
If an ABC class is set on the item record, it may be used when sorting for the count. Unfortunately, the capability is limited. On that note there is a related enhancement
Is there a way to move the Quantity Committed and Quantity Available columns in the Location detail all the way over to the left?
Customizing the View on the Item record > Location sublist is currently not possible. This may be done, however, if the Advanced Item Location Configuration is enabled on the account.
Can you print the count sheet before you've hit 'start count'?
The Count Sheet will only appear in the Print Inventory Count Sheet page after 'Start Count' has been clicked.
How would barcode scanners help in this inventory count?
Currently, this feature is logged as an enhancement request under Enhancement # 337860 "Bar Code: Inventory Count > Increase Count Quantity by 1 Each Time an Item Bar Code is Scanned". But scanning items is possible with the Warehouse Management System (WMS). You may check SuiteAnswers ID 98634 or reach out to your Account Manager for more information on WMS.
I see once you have started the count and hit 'edit count' you have a button that says 'void'. I don't see that button on my screen when I do this. Why is that?
The void button is available in Edit mode. If it is not available on your end even if you are in Edit mode, then, it is possible that the "Void Transactions Using Reversing Journals" preference is enabled in your account. You may also check SuiteAnswers ID 61670 for your reference.
I notice that you have bar codes on the Count Sheet - does that ability come with standard Net Suite or is it a separate module?
To be able to use bar codes, the Bar Codes and Item Labels feature must be enabled. Visit SuiteAnswers 28085 and 101958 for more information.
Can you see the GL impact of an inventory count before you approve it?
Inventory counts do not have GL impacts because these are non-posting transactions, and they only track the quantities of items. Once an Inventory Count is completed, Inventory Adjustments should be created for the difference between the count and on hand quantity.
Do you have standard Service level reports and Inventory Aging report?
All inventory related reports are available under Reports > Inventory/Items. Unfortunately, there is no available standard report for Inventory Aging Report. This is currently logged under Enhancement # 44650. An available workaround is documented under SuiteAnswers 75940.
Do you have inventory aging report?
Currently, there is no available report for Inventory Aging Report. This is currently logged under Enhancement 44650. You may check out SuiteAnswers 75940 as a workaround instead.
Since we do not use Suite Approvals, can this be done with the Approval Routing flow?
This can be done with enabled Approval Routing.
Can you use auto-calculated ROP for items that do not have sales orders but are components with WO demand?
Yes, Work Orders are considered as demand when Orders is selected in the Inventory Management Preferences > Transactions to Consider.
Can you create an automatic cycle count list based on product usage/sales? For example, can a list be created for the top 100 items sold for that week, month, or year? Or would this list have to be manually created?
It seems that this is not yet available in the standard NetSuite Account but, may be achievable through scripts/workflows.
In order to have access to the Item 360 Dashboard, do you have to have an additional Add-on?
Item 360 Dashboard is available in the SuiteApp Marketplace. You may check SuiteAnswers ID 107444 and the related topics.
How could it be that I don't have access to some of the here mentioned inventory features?
Kindly check if required features are enabled on your Account. And if you are using a Custom Role, it has sufficient permissions to the records.
Once the count is approved, is the Journal entry booked automatically to the P&L and reduce/increase inventory?
Once approved, an Inventory Adjustment transaction would be created for the Inventory count. The accounting impact will be reflected on that transaction.
I received an email notification from NetSuite regarding a change / update to "Inventory Status Change". Can you explain what "Inventory Status Change" does / its function.